MT6100IV2 - Single-Phase Smart Energy Metering Module
1. Core Metering Performance:
Accuracy Class: Compliant with IEC 62053-21/22 for Class 1 or Class 0.5S active energy, and Class 2 reactive energy.
Metering Chip: Integrates a high-performance energy measurement IC (e.g., a chip like AGP3300 or similar).
Measurement Functions:
Energy: Cumulative active energy (Import/Export), reactive energy (Quadrants I & IV).
Power Values: Instantaneous active (P), reactive (Q), and apparent (S) power.
Power Quality: RMS voltage, RMS current, line frequency, power factor.
Tamper Detection: Supports detection of reverse current, magnetic tamper (via external sensor), neutral disconnect, and potential relay bypass.
2. Module Hardware Architecture:
Host Microcontroller (MCU): Typically an ultra-low-power 32-bit ARM Cortex-M0/M3 core, responsible for data processing, communication control, and display driving.
Memory:
Program Flash: Sufficient for meter firmware and application code.
Data EEPROM / FRAM: For secure storage of energy data, billing parameters, and event logs.
RAM: For real-time operation.
Real-Time Clock (RTC): Integrated hardware RTC with battery backup for time-of-use (TOU) tariffing and event timestamping.
Power Supply: Wide input range (e.g., 12-24V AC/DC or direct from AC line) with ultra-low standby consumption.
3. Communication & Interfaces (Key Differentiator for a Module):
Infrared (IR) Interface: Compliant with DL/T645 or ANSI C12.18 protocol for local configuration and reading.
RS-485 Interface: One or two channels, supporting MODBUS or DL/T645 protocol for wired remote communication.
Optional Wireless Interfaces:
PLC (Power Line Carrier): Integrated or connector-ready for G3-PLC, PRIME, or other standards.
RF (Radio Frequency): Sub-GHz (470/868/915 MHz) or NB-IoT / 4G CAT-M1 module interface for cellular IoT connectivity.
Optical Port (IEC 62056-21): For initial commissioning and diagnostics.
Pulse Outputs: Isolated S0/KYZ pulse outputs for active and reactive energy for testing or external counters.
LCD Driver: Direct drive for segment LCD displays (e.g., 6+1 digits, with icons).
General-Purpose I/O (GPIO): For buttons, LEDs, tamper sensor inputs, and relay control.
4. Electrical Parameters (Module Level):
Parameter Symbol Conditions Min Typ Max Unit
Operating Voltage Range VMOD - 12 24 / 220 (AC) 57 (DC) or 264 (AC) V (AC/DC)
Standby Power Consumption PSB Communication off - < 0.5 1.0 W
Current Input Range IIN Via CT or Shunt 0.25% Ib - 20 x Imax A
Voltage Input Range VIN - 0.7 Vnom 220 / 230 / 240 1.2 Vnom V AC
Active Energy Error Err Ib, PF=1 - < ±0.5% - %
Operating Temperature TA - -40 25 +70 or +85 °C
Storage Temperature TSTG - -40 - +85 °C
Dimensions (PCB) - - - Approx. 100mm x 70mm - mm
5. Software & Certifications:
Pre-Loaded Firmware: Provides core metering, data management, and communication stack functions.
DL/T645 or IEC 62056 Protocol Stack: Pre-integrated for China or international markets.
Pre-Certification: May come with pre-certification for CE, MID (for EU), or national standards for EMC and metering accuracy.
6. Typical Application:
This module is designed to be the core board of a single-phase smart meter. Manufacturers add an enclosure, current sensors (CT or shunt), voltage terminals, a display, and an antenna (if wireless) to create a complete meter product.